> Formations > SolidWorks - Simulation Calculation Advanced
Course : SolidWorks - Simulation Calculation AdvancedOfficial Dassault Systèmes course, SolidWorks exam preparation
Practical course - 2d
- 14h00 - Ref. SWV
|
Download in PDF format
Share this course by email
 | Perform structural and thermal analyses in SolidWorks Simulation |
| Analyze and optimize the structural behavior of SolidWorks models |
| Master frequency analysis, drop testing and optimization |
Intended audience
Design office technicians, draftsmen, engineers. Anyone with experience of 3D design software.
Prerequisites
Avoir suivi la formation « SolidWorks Simulation Calcul Base » (Réf. SWU) ou avoir des connaissances équivalentes.
Certification
This training course provides the foundations needed for CSWP-Simulation certification, although it is not specifically dedicated to the exam.
Comment passer votre examen ?
Comment passer votre examen ?
Practical details
Teaching methods
Training in French. Official course material in digital format and in English. Good understanding of written English.
Course schedule
1 Frequency analysis of parts
- Principle of modal analysis.
- Analyse fréquentielle avec déplacements imposés.
- Frequency analysis without imposed displacement.
- Frequency analysis with loading.
Hands-on work
Case study: diapason
2 Frequency analysis of assemblies
- Contact management.
Hands-on work
Case study: engine mount
3 Buckling analysis
- Linear buckling analysis.
- Buckling safety factors to assess the stability of our design.
Hands-on work
Case study: particle separator
4 Load case management in simulation
- Load cases.
- Use the load case manager tool to combine loads.
Hands-on work
Case study: scaffolding
5 Under modeling
- Under modeling.
- Parent study (study on an isolated part of the scaffolding).
- Child study (study on an isolated part of the scaffolding).
Hands-on work
Case study: scaffolding
6 Topology analysis
- Topology analysis.
- Definition of optimization limits and objectives.
- Application of manufacturing control to design.
Hands-on work
Case study: mechanical linkage of a bicycle rear shock absorber
7 General thermal analysis
- Thin components.
- Fundamentals of thermal analysis.
- Steady-state thermal analysis.
- Transient thermal analysis.
- Transient analysis with time-varying loading.
- Transient thermal analysis using a thermostat.
Hands-on work
Case study: chip assembly
8 Thermal analysis with radiation
- Steady-state analysis with radiation.
Hands-on work
Case study: spotlight assembly
9 Advanced thermal stresses-2D simulation
- Thermal stress analysis.
- Thermal analysis with 2D simplification.
- Thermal stress analysis.
- Comparison with a 3D approach.
Hands-on work
Case study: metal expansion joint
10 Fatigue analysis
- Review of fatigue (stages of fatigue failure, cycle fatigue, high-low).
- Fatigue based on life-stress (S-N).
- Thermal study.
- Thermal stress study.
- Fatigue terminology.
- Fatigue study.
- Fatigue study with permanent loading.
Case study
11 Variable amplitude fatigue
- Variable amplitude fatigue study.
Hands-on work
Case study: suspension
12 Drop and impact test simulation
- Drop test analysis.
- Rigid floor drop test.
- Fall test on elastic floor.
- Drop test with elastoplastic material model.
- Drop test with contact interaction.
Hands-on work
Case study: camera
13 Optimization analysis
- Optimization analysis.
- Static and frequency analysis before optimization.
- Optimization analysis.
- Design study.
Hands-on work
Case study: press frame.
14 Pressure vessel analysis
- Analysis of a pressurized container.
- Flange and cover for manhole nozzle.
Hands-on work
Case study: pressurized tank
Publication date : 02/20/2025
PARTICIPANTS
Design office technicians, draftsmen, engineers. Anyone with experience of 3D design software.
PREREQUISITES
Avoir suivi la formation « SolidWorks Simulation Calcul Base » (Réf. SWU) ou avoir des connaissances équivalentes.
TRAINER QUALIFICATIONS
The experts who lead the training courses are specialists in the subjects covered. They are approved by the publisher and certified for the course. They have also been validated by our teaching teams in terms of both professional knowledge and teaching skills for each course they teach. They have at least three to ten years of experience in their field and hold or have held positions of responsibility in companies.
TERMS AND DEADLINES
Registration must be completed 24 hours before the start of the training course.
ACCESSIBILITY FOR PEOPLE WITH DISABILITIES
Do you have specific accessibility requirements? Contact Ms FOSSE, disability advisor, at the following address: psh-accueil@orsys.fr so that we can assess your request and its feasibility.
Design office technicians, draftsmen, engineers. Anyone with experience of 3D design software.
PREREQUISITES
Avoir suivi la formation « SolidWorks Simulation Calcul Base » (Réf. SWU) ou avoir des connaissances équivalentes.
TRAINER QUALIFICATIONS
The experts who lead the training courses are specialists in the subjects covered. They are approved by the publisher and certified for the course. They have also been validated by our teaching teams in terms of both professional knowledge and teaching skills for each course they teach. They have at least three to ten years of experience in their field and hold or have held positions of responsibility in companies.
ASSESSMENT TERMS
Assessment of targeted skills prior to training.
Assessment by the participant, at the end of the training course, of the skills acquired during the training course.
Validation by the trainer of the participant's learning outcomes, specifying the tools used: multiple-choice questions, role-playing exercises, etc.
At the end of each training course, ITTCERT provides participants with a course evaluation questionnaire, which is then analysed by our teaching teams. Participants also complete an official evaluation of the publisher.
An attendance sheet for each half-day of attendance is provided at the end of the training course, along with a certificate of completion if the participant has attended the entire session.
Assessment of targeted skills prior to training.
Assessment by the participant, at the end of the training course, of the skills acquired during the training course.
Validation by the trainer of the participant's learning outcomes, specifying the tools used: multiple-choice questions, role-playing exercises, etc.
At the end of each training course, ITTCERT provides participants with a course evaluation questionnaire, which is then analysed by our teaching teams. Participants also complete an official evaluation of the publisher.
An attendance sheet for each half-day of attendance is provided at the end of the training course, along with a certificate of completion if the participant has attended the entire session.
TEACHING AIDS AND TECHNICAL RESOURCES
The teaching resources used are the publisher's official materials and practical exercises.
The teaching resources used are the publisher's official materials and practical exercises.
TERMS AND DEADLINES
Registration must be completed 24 hours before the start of the training course.
ACCESSIBILITY FOR PEOPLE WITH DISABILITIES
Do you have specific accessibility requirements? Contact Ms FOSSE, disability advisor, at the following address: psh-accueil@orsys.fr so that we can assess your request and its feasibility.
This programme is an original creation, developed by the teaching teams at ORSYS Formation. Any reproduction, representation, adaptation or use, in whole or in part, without the prior written authorisation of ORSYS, is strictly prohibited. ORSYS reserves the right to take any action necessary to protect its intellectual property rights.
This programme is an original creation, developed by the teaching teams at ORSYS Formation. Any reproduction, representation, adaptation or use, in whole or in part, without the prior written authorisation of ORSYS, is strictly prohibited. ORSYS reserves the right to take any action necessary to protect its intellectual property rights.